Kalkulator UPS dla systemów CCTV i zabezpieczeń
Oblicz wymagane parametry VA zasilacza UPS i pojemność banku baterii dla swojego obciążenia CCTV, NVR, przełącznika PoE i kontroli dostępu. Wprowadź urządzenia i docelowy czas podtrzymania — wyniki aktualizują się na bieżąco.
boltSzybkie dodawanie obciążenia
| Nazwa urządzenia | Ilość | Moc | |
|---|---|---|---|
| storage16ch NVR Recorder | W | ||
| storageIP Camera | W | ||
| storagePoE Switch | W | ||
| storageMonitor | W | ||
add_circle | W | ||
| Całkowite obciążenie mocą | 320W | ||
Napięcie robocze systemu do wymiarowania banku baterii.
speedAnaliza systemu
Obliczony czas pracy przy 320W ciągłym obciążeniu
Wymagana pojemność UPS
Rozmiar banku baterii
Jak używać kalkulatora UPS
Dodaj każde urządzenie w swoim systemie zabezpieczeń za pomocą przycisków szybkiego dodawania lub wiersza niestandardowego urządzenia na dole tabeli. Dostosuj ilość i moc w watach dla każdego elementu — wartości watowe są edytowalne bezpośrednio w tabeli, dzięki czemu możesz dopasować rzeczywiste dane techniczne sprzętu z karty katalogowej. Po uzupełnieniu listy obciążeń ustaw żądany czas podtrzymania i napięcie banku baterii. Wymagana ocena VA i pojemność baterii aktualizują się w czasie rzeczywistym.
Wymiarowanie UPS dla systemów CCTV i zabezpieczeń
Prawidłowo zwymiarowany UPS dla instalacji zabezpieczeń musi uwzględniać trzy rzeczy: całkowity ciągły pobór mocy wszystkich podłączonych urządzeń, docelowy czas pracy podczas awarii zasilania sieciowego oraz straty w etapach baterii i falownika. Niedoszacowanie oceny VA grozi wyłączeniem UPS pod obciążeniem; niedoszacowanie banku baterii oznacza, że system wyłączy się przed osiągnięciem docelowego czasu pracy.
Kalkulator stosuje współczynnik korekcji mocy 0,8 — standardowe założenie dla zasilaczy impulsowych używanych w NVR, przełącznikach PoE i kamerach IP — aby przeliczyć obciążenie w watach na ocenę VA. Pojemność baterii jest obliczana z uwzględnieniem sprawności falownika, sprawności ładowania/rozładowania baterii oraz limitu głębokości rozładowania 50%, który jest standardowym zaleceniem dla baterii kwasowo-ołowiowych i AGM w celu zachowania żywotności.
Typowy pobór mocy urządzeń systemu zabezpieczeń
Pobór mocy znacznie różni się między typami i modelami urządzeń. Wartości w przyciskach szybkiego dod
- IP cameras (fixed, PoE Class 2–3): 8–15W per camera
- PTZ cameras: 20–30W, higher during pan/tilt movement
- 4ch NVR: 15–25W
- 16ch NVR: 30–60W depending on HDD count
- 32ch NVR: 60–120W with multiple HDDs under load
- 8-port PoE switch: device consumption 8–15W plus full PoE budget if cameras are connected directly
- Access control panels: 10–25W, plus door lock strikes and readers
- Monitors (24"): 20–35W depending on brightness
Note that PoE switches supply power to cameras through the network port. If your cameras are powered by a PoE switch, add the switch's total PoE budget (not just its base consumption) to your load calculation, or list cameras and switch separately as done in this calculator's presets.
Battery Bank Voltage: 12V, 24V, or 48V?
The battery voltage setting determines how the required energy capacity is translated into amp-hours. All three voltages produce the same energy output — the choice affects how many batteries are needed and how they are wired.
A 12V system is common for small installations with a single battery. A 24V system (two 12V batteries in series) is standard for mid-sized CCTV racks and reduces cable losses at the same power level. A 48V system is used in larger installations and telecom-style cabinets where high capacity is needed with lower current draw. Match the voltage setting to your actual battery bank configuration.
Frequently Asked Questions
What VA rating UPS do I need for a CCTV system?
Add up the wattage of all devices — NVR, cameras, PoE switch, monitors — and divide by 0.8 to get the minimum VA rating. A 300W total load requires at least a 375VA UPS. It is good practice to size the UPS at 20–25% above the calculated minimum to allow headroom for startup surges and future load additions.
How long will a UPS run a CCTV system?
Runtime depends on the battery bank capacity, the total load in watts, and the efficiency of the system. A larger battery bank extends runtime proportionally. This calculator sizes the battery bank for a target runtime you specify — set your required backup duration and the tool returns the Ah capacity needed for your battery bank at the chosen voltage.
Should I use a 12V or 24V battery for a security system UPS?
For small systems (one NVR, a few cameras, under 150W), a single 12V battery is usually sufficient. For larger installations, a 24V bank (two 12V batteries in series) gives you more capacity in a manageable form factor and reduces current, which lowers cable and connector losses. The battery bank voltage in this calculator does not change the energy result — only the amp-hour figure changes to reflect the voltage.
Can I use a standard office UPS for CCTV?
Yes, for short runtimes. Standard office UPS units (typically 5–15 minutes at full load) are adequate for graceful shutdown protection. For security applications requiring 2–8 hours of backup, you need a UPS with an external battery connection or a dedicated DC power backup unit sized to the calculations above.
Gotowy do stworzenia planu systemu zabezpieczeń?
Rozwiń te obliczenia — zaprojektuj pełny rozkład kamer, poprowadź kable i wygeneruj profesjonalną propozycję w formacie PDF.